How to Hook Up an Old Antenna to a New TV
A big antenna in the attic and a flat wire that fits nothing on the back of the TV. One small part joins them, and a scan tells you if it was worth it.
As an Amazon Associate I earn from qualifying purchases.
Two ways to read this piece. The quick read tells it in three pictures and a few short paragraphs. The full story is the whole piece, with every source.

Old ribbon wire, new TV, no way to join them
Anyone whose house came with an antenna in the attic has met the wire too. That ribbon carries a conductor down each edge, and the socket on a new TV is built for round coax.
Age isn't the problem. One attic antenna went up in 1985 and works today. A second owner says theirs works fantastic, and at Low End Mac a 1970s model on a digital TV turned up 21 channels.

Two screws for the wire, one plug for the TV
The join is a push-on matching transformer, sold under that name or as a balun. In the r/cordcutters attic-antenna thread, the answer to a photo of an antenna still on its ribbon was a quick push-on plug and a scan.
The ribbon's two bare ends go under its screws, and the plug on the other side presses onto the TV's socket. Look for 300 to 75 in the listing, the ribbon's ohms to the coax's.

Let the TV judge the antenna
Once it's on, go to the TV's settings and scan for channels, the first step one reply names. Then dig out the live signal meter, maybe under Support, Help or System Information. Its strength and quality numbers move live, so a helper in the attic can turn the antenna until they climb.
An empty scan points at the old cable, which one reply said may need replacing with new coax. Get the push-on part first, and let the scan settle it.
Want the details?
The full story has the rest, the annoying parts included, and every source.
Behind a new TV there's one round socket for an antenna. The wire that comes down from the attic is nothing like it. It's a flat ribbon with a wire along each edge, and there's nowhere on the TV to put either one.
That mismatch is the whole job. The socket on the TV changed, but the antenna didn't.
If your house came with an antenna in the attic and no way to plug it in, you don't need a new antenna to find out whether this one still works.
What is the flat wire?
Antennas used to come down to the TV on that flat ribbon, and its name is twin lead. The round cable a new TV takes is coax.
In r/Oldhouses, somebody with a big antenna upstairs was told that coax still needs a matching transformer where it meets wire like this.
Will an old antenna work for digital?
The antenna doesn't mind what year it is. Someone whose attic antenna has been up there since 1985 put it this way:
The antenna doesn't care if the broadcast signal encoded on the rf carrier is digital or analog. It's your TV's tuner that does the decoding, not the antenna.
u/silverbullet52, in r/cordcutters
An old antenna can still do the job. Several people with one in the attic say theirs works great, and one says attic antennas beat the window kind and stay hidden.
Back in 2014, Adam Geller at Low End Mac put a 1970s antenna on a digital TV with a matching transformer and a long run of coax. The setup found 21 channels, several of them HD.
The part that joins them
The matching transformer is the part, and the listing may say balun, which is the same thing. One side has two screws that take the flat wire's two ends. The other side is a round plug that pushes onto the TV's antenna socket.
The 300 and 75 you'll see in its name are ohms, one number for the flat wire and one for coax, and bridging them is all it does.
In the r/cordcutters attic-antenna thread that quote came from, the antenna still had its flat wire attached. The reply was to get a push-on matching transformer, the kind sold as a 300 ohm to 75 ohm quick push-on plug. Then scan for channels and see what it picks up.
Pick one that ends in a push-on plug, because that end goes straight onto the TV, with nothing else to buy between the wire and the set. Loosen the two screws, put one bare end of the flat wire under each, tighten, and push the plug onto the socket on the back of the TV.
Run a scan, then find the signal meter
Nobody online can tell you whether wire that's sat in your walls for decades still carries a signal. The TV can.
The first move with an inherited antenna is to hook it up and run a channel scan. It lives in the TV's settings.
The signal meter says what's coming through now, where a scan only says what came through once. The meter may sit under a menu like Support, Help or System Information, or near the scan itself. Watching strength and quality change in real time makes the antenna far easier to judge.
Leave it on screen while somebody in the attic turns the antenna, and you can aim it by the numbers.

Is it even a TV antenna?
The person who started the old-house thread had a wall plate with two pins and wanted to hook the attic antenna up through it. One reply read the plate before anybody got to the wiring.
It was for a radio console, one pin to an aerial in the attic and the other to a ground wire clamped on a pipe. The plate turned out to be marked Radio Aerial.
The antenna can be a radio one as well. The old S-curve kind was made for FM in the console-stereo days, and on TV it's hit or miss.
A photo won't settle it, though. One person was told from a photo that the antenna in their attic was that FM kind, but it turned out to be a TV one. They hooked up a tuner and got almost 50 channels.
A radio hookup is the one thing the part can't turn into TV. The part's cheap and the scan's free, so try it anyway, but go in knowing what the house may have left you.
When the scan comes up empty
The old wire is the first suspect. One reply in the attic-antenna thread called the cable the biggest concern and said a new run of coax, the kind sold as RG6, might be needed. Geller says coax holds up better than the flat ribbon, so if you're pulling new wire anyway, pull that.
The other route skips the old wiring altogether. Someone in the old-house thread bought an attic-mount antenna and dropped a new coax line down the wall beside the old wire, which their house's framing made easy, though yours might not.
Whatever you run, the antenna is the only thing that lives up there. One person who put a DVR in the attic found it didn't last the summer heat, and the reply was blunt: only the antenna goes in the attic.

Start at the TV end. Put the two ends under the screws of a push-on matching transformer, press the plug onto the TV, and run the scan.
A full list of channels and you're done for the price of a very small part. An empty one, and the next thing to look at is the wire.

