How to Make Old Wooden Drawers Slide Easier
The drawer comes out halfway and hangs. Wax is where woodworkers start on a wood-on-wood drawer, but there's a next step for the one wax doesn't fix.
As an Amazon Associate I earn from qualifying purchases.
Two ways to read this piece. The quick read tells it in three pictures and a few short paragraphs. The full story is the whole piece, with every source.

Wood on wood, and the wood has worn
An old drawer has no metal slide, just its own wood on wooden rails, and generations of pulling leave worn grooves in them.
If an old chest, desk or built-in has a drawer that fights you on every pull, the fix comes in an order.
Square comes first. One Sawmill Creek member measures the opening against the drawer, and another checks the diagonals. Out of square gets a plane or a belt sander.

Wax first, then tape for the stubborn one
Then comes wax, paste wax on the drawer sides and a candle on the rails, says a Sawmill Creek moderator. For one old house, canning wax was the whole fix.
One new-build drawer stayed stuck through coat after coat of wax. UHMW strips on the runner freed it.
The same plastic comes as TapeCase UHMW tape, sticky on one side. It puts a slippery layer between drawer and rail, and Cool Tools recommends it for antique drawers that rub and stick.

Make a little room, then it rides level
The tape needs room, and one Sawmill Creek member says as much. The woodworker with the new drawer took 1/32 of an inch off its bottom first.
Then the drawer runs level and the wood stops wearing. Two short pieces did that for a Fine Woodworking member's hundred-year-old chest, and a future owner can peel them off.
Wax every drawer first, and buy a roll of the tape only for the one wax doesn't cure. Expect a little sanding.
Want the details?
The full story has the rest, the annoying parts included, and every source.
An old drawer runs on nothing. Its sides and bottom ride on wooden rails inside the cabinet, wood on wood. After enough decades the rails wear and the drawer drags, and every pull turns into a lift and a wiggle.
The usual advice online is a bar of soap or a candle. That's not wrong, but it's one step of three. The woodworkers in the forums do this job in an order: check the drawer is square, wax it, and only then reach for a slick tape that stops the two surfaces gripping each other.
If you've got an old dresser, desk or built-in whose drawers need a shove, this is the order, and where the tape fits.
Check the drawer is square first
In a Sawmill Creek thread on sticking drawers, one member wants you to measure the openings before anything else, at the front and the back of the cabinet, side to side and up and down. Then put a tape measure on the drawer and compare.
Another member says to measure the diagonals, left front to right rear and right front to left rear, and bets the drawers or the cabinet are out of square.
A drawer or an opening that's out of square needs wood taken off before any wax goes on. The first member's fix for that is a small bench plane or a belt sander.
Then wax it
Wood sliding on wood wants wax. A moderator in that thread has the recipe: paste wax on the drawer sides, and a candle rubbed on the runners and on the rails in the cabinet. Another reply calls that a great first step for any sticking drawer that's wood on wood.
Sometimes wax is the only fix you'll need. One member waxed every drawer in a very old house and put it like this:
I used wax (canning wax found in the supermarket) and rubbed a lot on and they all run smoothly. Some have light loads and some have heavy loads. It is a simple and very cheap solution.
Ellen Benkin, in the Sawmill Creek thread

When wax isn't enough
A woodworker on Woodtalk put several coats of wax on a drawer, hours between them, then tried beeswax, but it still stuck. That was a new build rather than an old drawer. Still, what fixed it is what people with old drawers reach for: strips of UHMW on the runner.
UHMW tape is that material with adhesive on the back. The letters stand for ultra-high-molecular-weight polyethylene, which is why everybody says UHMW.
It's a very slippery plastic, and Jordan Bunker's review at Cool Tools puts it on exactly this job: antique wooden drawers that rub and stick. The roll in the review is from TapeCase, the same series as the link above.
In r/centuryhomes, one owner put it on the runners of every drawer in the house, and the old drawers now "slide like buttah". That owner reckons it's basically the stuff on the feet of a computer mouse.
Other woodworkers use it too. On Woodweb, one says adhesive-backed slick tape on wood slides worked great on a well-loaded drawer with a cherry front. Another has used it as the case rail under the drawer side, in new builds and for repairing worn grooves in antiques.
The tape goes on the surfaces that rub. That means the runners the drawer rides on, and one Sawmill Creek member adds the sides and underneath of the drawer.
A 2002 reply on the Fine Woodworking forum gets by on two short pieces: one under the back of the drawer, and one at the front of the rail it slides on. That keeps the drawer level, and the reply says it stops the wood wearing any further.
Does the tape need room?
A little, and this is the catch. The Sawmill Creek member who recommends it says it works well if there's sufficient room. On Woodtalk, one reply warned it adds a small amount of thickness to deal with, worth a little sanding if the tape works as well as people say.
What that took on the Woodtalk drawer was 1/32 of an inch off the bottom to make room for the strips.
Make room first, then sand the wood smooth where it meets the tape. A UHMW manufacturer on Woodweb has seen splinters lodge in the material and make the drawers stick, so the wood facing it needs to be well sanded.
On a real antique it's a cheat, and the Fine Woodworking reply says so: not in keeping with a 100-year-old chest. It doesn't alter the piece, though, and a future owner can take it off.

Start at the cheap end. Measure the opening, wax the sides, run a candle over the runners and rails, and see how many drawers that settles.
The one that still hangs after wax is the one for a roll of UHMW tape. It goes on the runners, with a sliver taken off first so there's room for it to ride.

